AVIATION PLATINUM
CERAMIC COATING
Certifications:
BOEING + SGS
NOTE:
First, remove any oxidation and staining before application.
Clean the surfaces thoroughly with (Step #1) TFS PRE-WASH.
(Step #2) Apply 5 - 6 drops of TFS AVIATION PLATINUM to microfiber applicator until pad is saturated. Start with a 2’ X 2’ square section and wipe left to right until product is overlapped evenly.
Once the product has flashed (rainbow look) and appears not to be wet, thoroughly wipe the panel with a microfiber towel to create a flat even finish.
Move to the next section and repeat.
Temperature and humidity will directly affect the flash time. To layer TFS AVIATION PLATINUM, allow 1 hour between coats. Pads and towels should be rinsed, bagged and disposed of properly.
Note: Temperature and humidity will directly effect the curing time (flashing point) of Platinum. Test a spot before completely starting.
AVIATION TITANIUM
PAINT SEALANT
Certifications:
BOEING, AIRBUS, AMS + US MILITARY
Shake well.
Complete Step #1 TFS AVIATION PRE-WASH.
Make sure surface is dry.
Apply small amount onto a clean foam applicator, orbital foam pad or bonnet.
Apply in a circular motion.
Cover the section with a thin coat.
Repeat this process for all painted surfaces.
Allow to dry for an hour.
Buff off with a microfiber towel.
AVIATION PRE-WASH
TITANIUM +
PLATINUM
NOTE:
Alcohol and water based product with mild surfactants for general cleaning.
If painted surfaces are extremely dirty, clean with a detergent first.
Spray on to the painted surface area and wipe thoroughly with a towel until dry.
Proceed to (Step #2) TFS AVIATION PLATINUM or TFS AVIATION TITANIUM.
ULTIMATE DEGREASER
EXTERIOR
Spray onto surface.
Let stand for 30 seconds. If heavily soiled - let stand 2 to 5 minutes.
Can be used as a dry wash or rinse with water and wipe clean.
Follow up with one of TFS dry washes.
SILICA DRY WASH
EXTERIOR
NOTES:
If streaking occurs, dilute with water if necessary.
Avoid spraying on hot surfaces.
READY TO USE
Shake well.
Spray mist onto small area.
Rub the surface using a soft clean terry cloth or microfiber towel.
Turn cloth over and buff to a high gloss.
RUBBING COMPOUND
EXTERIOR
Shake well before using.
Apply TFS RUBBING COMPOUND evenly to a 2 ft by 2 ft area.
Using a rotary polisher or random orbital polisher, slowly buff using an overlapping pattern with enough pressure to eliminate surface defects.
As the compound material diminishes, finesse the paint surface - progressively using less pressure until a high gloss is achieved.
Follow up with TFS SWIRL REMOVER, TFS TITANIUM PAINT PROTECTION or TFS PLATINUM CERAMIC COATING.
SWIRL REMOVER
EXTERIOR
Shake well.
Use a wool pad for moderate imperfections or foam pad for light imperfections with a high speed rotary polisher or a random orbital polisher.
Apply evenly to a cool, clean 2 ft by 2 ft area.
Begin buffing slowly using light to moderate pressure.
Decrease pressure as imperfections and swirls disappear.
CARPET CLEANER
INTERIOR
NOTES:
Spot cleaning:
Pretest on an inconspicuous area! Use undiluted with a towel.
Upholstery Pre-Spray:
Dilute 1 part TFS CARPET CLEANER to 15 parts water and apply through sprayer.
Agitate carpet with rake or pile brush.
Wait 5-10 minutes and extract.
FABRIC SPOT REMOVER
INTERIOR
NOTES:
Pretest on an inconspicuous area.
Use 16oz TFS FABRIC SPOT REMOVER per gallon of water.
CONCENTRATED
Spray or soak surface to be cleaned.
Allow 10-30 minutes dwell time, clean as usual. If needed, extract area.
STREAK-FREE CLEAN
INTERIOR
NOTES:
Pretest on an inconspicuous area.
Do not use if color or texture is affected.
READY TO USE
Mist on surface. Do not saturate.
Wipe dry with clean towel, until towel remains clean.
INTERIOR CLEANER
INTERIOR
NOTES:
Pretest on an inconspicuous area.
Do not use if color or texture is affected.
READY TO USE
Mist on surface. Do not saturate.
Wipe dry with clean towel, until towel remains clean.
LEATHER CLEANER
INTERIOR
NOTES:
Pretest on an inconspicuous area.
Do not use if color or texture is affected.
Ready to use, do not dilute.
Mist on surface, do not saturate or soak leather.
Wipe or rub surface with clean towel or damp sponge.
Wipe dry with clean towel, until towel remains clean.
Follow up with TFS LEATHER CONDITIONER.
For heavy duty cleaning, allow time to penetrate and scrub surface if necessary.
LEATHER CONDITIONER
INTERIOR
NOT FOR USE ON SUEDE.
Pour a small amount onto clean towel or applicator pad
Work into leather with towel, applicator pad or very soft bristle brush.
Wipe off excess cleaner and buff with clean soft towel.